DDR V1.17 992b933606 typ 23/04/25-10:10:19
In
LP4/4x derate en, other dram:1x trefi
ddrconfig:7
LPDDR4X, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS1 Row=17 CS=2 Die BW=8 Size=8192MB
tdqss: cs0 dqs0: 48ps, dqs1: -72ps, dqs2: -24ps, dqs3: -120ps,
tdqss: cs1 dqs0: 72ps, dqs1: -96ps, dqs2: -48ps, dqs3: -120ps,

change to: 324MHz
clk skew:0x60

change to: 528MHz
clk skew:0x58

change to: 780MHz
clk skew:0x58

change to: 1560MHz(final freq)
PHY drv:clk:36,ca:36,DQ:29,odt:60
vrefinner:16%, vrefout:22%
dram drv:40,odt:80
vref_ca:00000071
clk skew:0x1c
cs 0:
the read training result:
DQS0:0x32, DQS1:0x32, DQS2:0x35, DQS3:0x32,
min  : 0xd  0xf 0x13  0xf  0x1  0x6  0xa  0x5 , 0xa  0x8  0x2  0x3 0x10  0xc  0xd  0x8 ,
      0x12 0x10  0xd  0xd  0x4  0x2  0x5  0x5 , 0xd  0xa  0x8  0x2 0x12 0x11  0xe 0x10 ,
mid  :0x28 0x29 0x2c 0x2a 0x1d 0x20 0x24 0x20 ,0x23 0x21 0x1c 0x1d 0x2a 0x25 0x27 0x22 ,
      0x2c 0x2b 0x27 0x27 0x1f 0x1c 0x1f 0x21 ,0x28 0x24 0x23 0x1e 0x2c 0x2c 0x29 0x2c ,
max  :0x44 0x44 0x45 0x46 0x39 0x3b 0x3e 0x3c ,0x3c 0x3b 0x37 0x37 0x44 0x3f 0x42 0x3d ,
      0x47 0x47 0x42 0x41 0x3a 0x37 0x39 0x3d ,0x44 0x3f 0x3e 0x3b 0x47 0x47 0x45 0x49 ,
range:0x37 0x35 0x32 0x37 0x38 0x35 0x34 0x37 ,0x32 0x33 0x35 0x34 0x34 0x33 0x35 0x35 ,
      0x35 0x37 0x35 0x34 0x36 0x35 0x34 0x38 ,0x37 0x35 0x36 0x39 0x35 0x36 0x37 0x39 ,
the write training result:
DQS0:0x25, DQS1:0xe, DQS2:0x18, DQS3:0x5,
min  :0x6a 0x6d 0x71 0x6b 0x5e 0x61 0x65 0x68 0x63 ,0x50 0x4c 0x46 0x4a 0x51 0x51 0x55 0x53 0x4b ,
      0x5f 0x5e 0x59 0x58 0x4e 0x4f 0x51 0x56 0x56 ,0x4b 0x49 0x46 0x45 0x50 0x4f 0x4f 0x54 0x49 ,
mid  :0x88 0x8a 0x8d 0x87 0x78 0x7d 0x81 0x81 0x7d ,0x6b 0x68 0x61 0x63 0x6c 0x6c 0x6e 0x6c 0x66 ,
      0x7a 0x7b 0x74 0x74 0x6a 0x69 0x6c 0x71 0x71 ,0x68 0x65 0x61 0x5e 0x6c 0x6c 0x69 0x6e 0x63 ,
max  :0xa6 0xa7 0xa9 0xa4 0x93 0x99 0x9d 0x9a 0x98 ,0x87 0x85 0x7c 0x7d 0x88 0x87 0x88 0x85 0x82 ,
      0x96 0x98 0x8f 0x91 0x87 0x84 0x87 0x8c 0x8c ,0x85 0x81 0x7c 0x78 0x89 0x89 0x84 0x89 0x7d ,
range:0x3c 0x3a 0x38 0x39 0x35 0x38 0x38 0x32 0x35 ,0x37 0x39 0x36 0x33 0x37 0x36 0x33 0x32 0x37 ,
      0x37 0x3a 0x36 0x39 0x39 0x35 0x36 0x36 0x36 ,0x3a 0x38 0x36 0x33 0x39 0x3a 0x35 0x35 0x34 ,
cs 1:
the read training result:
DQS0:0x33, DQS1:0x33, DQS2:0x34, DQS3:0x31,
min  : 0xd 0x10 0x13 0x10  0x1  0x8  0xa  0x5 , 0xa  0x8  0x1  0x3  0xf  0xc  0xe  0x8 ,
      0x11 0x10  0xd  0xb  0x2  0x0  0x6  0x5 , 0xb  0x8  0x8  0x1 0x13 0x10  0xd  0xf ,
mid  :0x27 0x29 0x2b 0x2a 0x1c 0x21 0x24 0x20 ,0x23 0x21 0x1b 0x1d 0x29 0x25 0x28 0x23 ,
      0x2b 0x2b 0x27 0x25 0x1d 0x1b 0x1f 0x20 ,0x25 0x22 0x22 0x1c 0x2c 0x2b 0x28 0x2b ,
max  :0x42 0x43 0x44 0x44 0x38 0x3b 0x3e 0x3b ,0x3d 0x3b 0x36 0x38 0x44 0x3f 0x43 0x3f ,
      0x46 0x46 0x42 0x3f 0x38 0x36 0x39 0x3b ,0x40 0x3c 0x3c 0x38 0x46 0x46 0x44 0x47 ,
range:0x35 0x33 0x31 0x34 0x37 0x33 0x34 0x36 ,0x33 0x33 0x35 0x35 0x35 0x33 0x35 0x37 ,
      0x35 0x36 0x35 0x34 0x36 0x36 0x33 0x36 ,0x35 0x34 0x34 0x37 0x33 0x36 0x37 0x38 ,
the write training result:
DQS0:0x25, DQS1:0xe, DQS2:0x18, DQS3:0x5,
min  :0x6f 0x74 0x76 0x72 0x63 0x69 0x6c 0x6d 0x6a ,0x49 0x45 0x3e 0x40 0x4b 0x4a 0x4c 0x4c 0x43 ,
      0x5b 0x5a 0x55 0x54 0x4b 0x4a 0x4d 0x52 0x51 ,0x4a 0x48 0x45 0x42 0x4f 0x4f 0x4b 0x53 0x47 ,
mid  :0x8d 0x90 0x92 0x8e 0x7f 0x84 0x87 0x87 0x83 ,0x65 0x61 0x59 0x5b 0x66 0x64 0x66 0x64 0x5f ,
      0x77 0x76 0x6f 0x70 0x66 0x65 0x68 0x6c 0x6c ,0x66 0x62 0x5e 0x5c 0x6b 0x6b 0x66 0x6d 0x61 ,
max  :0xab 0xad 0xaf 0xaa 0x9b 0x9f 0xa3 0xa2 0x9d ,0x81 0x7d 0x75 0x76 0x81 0x7e 0x81 0x7d 0x7b ,
      0x93 0x93 0x89 0x8c 0x82 0x81 0x84 0x87 0x87 ,0x83 0x7d 0x78 0x76 0x87 0x87 0x81 0x87 0x7b ,
range:0x3c 0x39 0x39 0x38 0x38 0x36 0x37 0x35 0x33 ,0x38 0x38 0x37 0x36 0x36 0x34 0x35 0x31 0x38 ,
      0x38 0x39 0x34 0x38 0x37 0x37 0x37 0x35 0x36 ,0x39 0x35 0x33 0x34 0x38 0x38 0x36 0x34 0x34 ,
CA Training result:
cs:0 min  :0x53 0x52 0x49 0x43 0x48 0x3f 0x4d ,0x50 0x4a 0x47 0x3e 0x48 0x3f 0x4d ,
cs:0 mid  :0x8f 0x90 0x85 0x82 0x84 0x7f 0x7d ,0x8d 0x8a 0x83 0x7f 0x83 0x80 0x7c ,
cs:0 max  :0xcc 0xce 0xc1 0xc2 0xc0 0xbf 0xad ,0xcb 0xca 0xbf 0xc0 0xbf 0xc1 0xac ,
cs:0 range:0x79 0x7c 0x78 0x7f 0x78 0x80 0x60 ,0x7b 0x80 0x78 0x82 0x77 0x82 0x5f ,
cs:1 min  :0x50 0x57 0x49 0x4a 0x4a 0x47 0x4f ,0x4d 0x51 0x43 0x45 0x45 0x47 0x4a ,
cs:1 mid  :0x91 0x91 0x88 0x84 0x88 0x81 0x82 ,0x8f 0x8c 0x83 0x80 0x85 0x82 0x7e ,
cs:1 max  :0xd3 0xcc 0xc7 0xbf 0xc7 0xbc 0xb6 ,0xd2 0xc7 0xc4 0xbb 0xc6 0xbd 0xb3 ,
cs:1 range:0x83 0x75 0x7e 0x75 0x7d 0x75 0x67 ,0x85 0x76 0x81 0x76 0x81 0x76 0x69 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-gaaca6ffec1-211203 #zzz (Dec 03 2021 - 18:42:16)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 9
spl: mmc init failed with error: -95
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
Trying fit image at 0x4000 sector
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256(0d5225a4ab...) + OK
## Checking uboot 0x00a00000 ... sha256(2a2eb1cde8...) + OK
## Checking fdt 0x00b3f4f0 ... sha256(036cca5880...) + OK
## Checking atf-2 0xfdcc1000 ... sha256(3e94d16e6a...) + OK
## Checking atf-3 0x0006b000 ... sha256(fde0ef262b...) + OK
## Checking atf-4 0xfdcce000 ... sha256(c9eb312bf2...) + OK
## Checking atf-5 0xfdcd0000 ... sha256(befba422b8...) + OK
## Checking atf-6 0x00069000 ... sha256(6ede7a3b44...) + OK
## Checking optee 0x08400000 ... sha256(4fcbcd3870...) + OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 237.898 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-607-gbf602aff1:cl
NOTICE:  BL31: Built : 10:16:03, Jun  5 2023
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid 220114
INFO:    dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC:
I/TC: OP-TEE version: 3.13.0-723-gdcfdd61d0 #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 ( Wed Jun  7 09:43:57 CST 2023 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9


U-Boot 2017.09 (Oct 26 2023 - 21:22:20 +0800)

Model: Rockchip RK3568 Evaluation Board
MPIDR: 0x81000000
PreSerial: 2, raw, 0xfe660000
DRAM:  7.7 GiB
Sysmem: init
Relocation Offset: ed220000
Relocation fdt: eb9f91c8 - eb9fecd8
CR: M/C/I
Using default environment

DM: v1
dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
boot mode: None
RESC: 'boot', blk@0x0001a59f
resource: sha256+
FIT: no signed, no conf required
DTB: rk-kernel.dtb
HASH(c): OK
I2c0 speed: 100000Hz
PMIC:  RK8090 (on=0x40, off=0x00)
vdd_logic init 1100000 uV
vdd_gpu init 950000 uV
vdd_npu init 900000 uV
io-domain: OK
INFO:    ddr dmc_fsp already initialized in loader.
Warn: can't find connect driver
Warn: can't get connect driver
Could not find baseparameter partition
Model: SMARTFLY YY3568 Board
MPIDR: 0x81000000
Rockchip UBOOT DRM driver version: v1.0.1
VOP have 2 active VP
vp0 have layer nr:3[1 3 5 ], primary plane: 5
vp1 have layer nr:3[0 2 4 ], primary plane: 4
vp2 have layer nr:0[], primary plane: 0
Using display timing dts
edp@fe0c0000:  detailed mode clock 138500 kHz, flags[a]
    H: 1920 1984 2016 2080
    V: 1080 1092 1099 1111
bus_format: 100e
VOP update mode to: 1920x1080p60, type: eDP0 for VP1
rk3036_pll_set_rate: wait pll lock timeout! pll_id=5
VP1 set crtc_clock to 138400KHz
VOP VP1 enable Smart0[403x233->403x233@758x423] fmt[1] addr[0xedf45000]
AUX CH command reply failed!
AUX CH command reply failed!
AUX CH error happens: 2
failed to read dpcd caps: -121
hdmi@fe0a0000 disconnected
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 1104000 KHz
  dpll 780000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  npll 1200000 KHz
  vpll 692000 KHz
  hpll 24000 KHz
  ppll 200000 KHz
  armclk 1104000 KHz
  aclk_bus 150000 KHz
  pclk_bus 100000 KHz
  aclk_top_high 500000 KHz
  aclk_top_low 400000 KHz
  hclk_top 150000 KHz
  pclk_top 100000 KHz
  aclk_perimid 300000 KHz
  hclk_perimid 150000 KHz
  pclk_pmu 100000 KHz
Net:   eth1: ethernet@fe010000, eth0: ethernet@fe2a0000
Hit key to stop autoboot('CTRL+C'):  0
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
No valid android hdr
Android image load failed
Android boot failed, error -1.
## Booting FIT Image at 0xe9344380 with size 0x024b3e00
Fdt Ramdisk skip relocation
## Loading kernel from FIT Image at e9344380 ...
   Using 'conf' configuration
## Verified-boot: 0
   Trying 'kernel' kernel subimage
     Description:  unavailable
     Type:         Kernel Image
     Compression:  uncompressed
     Data Start:   0xe9360780
     Data Size:    38369792 Bytes = 36.6 MiB
     Architecture: AArch64
     OS:           Linux
     Load Address: 0x00280000
     Entry Point:  0x00280000
     Hash algo:    sha256
     Hash value:   cdc44303d22cd33a560beb492d7dde2347a08f86a213b1377588ac84f199e004
   Verifying Hash Integrity ... sha256+ OK
## Loading fdt from FIT Image at e9344380 ...
   Using 'conf' configuration
   Trying 'fdt' fdt subimage
     Description:  unavailable
     Type:         Flat Device Tree
     Compression:  uncompressed
     Data Start:   0xe9344b80
     Data Size:    113238 Bytes = 110.6 KiB
     Architecture: AArch64
     Load Address: 0x08300000
     Hash algo:    sha256
     Hash value:   cee66ca665653ef6d7fc692b92236672756180d532b75de4e8a174e8040224ce
   Verifying Hash Integrity ... sha256+ OK
   Loading fdt from 0x08300000 to 0x08300000
   Booting using the fdt blob at 0x08300000
   Loading Kernel Image from 0xe9360780 to 0x00280000 ... OK
   kernel loaded at 0x00280000, end = 0x02717a00
   Using Device Tree in place at 0000000008300000, end 000000000831ea55
vp1 adjust cursor plane from 0 to 1
vp0, plane_mask:0x2a, primary-id:5, curser-id:1
vp1 adjust cursor plane from 1 to 0
vp1, plane_mask:0x15, primary-id:4, curser-id:0
vp2, plane_mask:0x0, primary-id:0, curser-id:-1
WARNING: could not set reg FDT_ERR_BADOFFSET.
## reserved-memory:
  drm-logo@00000000: addr=edf00000 size=114000
  drm-cubic-lut@00000000: addr=eff00000 size=8000
  ramoops@110000: addr=110000 size=f0000
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x100000000 - 0x200000000 (size: 0x100000000)
== DO RELOCATE == Kernel from 0x00280000 to 0x00200000
Total: 1141.950/1185.417 ms

Starting kernel ...

[    1.190459] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    1.190483] Linux version 5.10.160 (build@thinkpad) (aarch64-none-linux-gnu-gcc (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm 20210621, GNU ld (GNU Toolchain for the A-profile Architecture 10.3-2021.07 (arm-10.29)) 2.36.1.20210621) #13 SMP Thu Oct 26 19:30:59 CST 2023
[    1.195453] Machine model: SMARTFLY YY3568 Board
[    1.195525] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[    1.199576] printk: bootconsole [uart8250] enabled
[    1.201150] efi: UEFI not found.
[    1.322399] Zone ranges:
[    1.322647]   DMA      [mem 0x0000000000200000-0x00000000ffffffff]
[    1.323226]   DMA32    empty
[    1.323491]   Normal   [mem 0x0000000100000000-0x00000001ffffffff]
[    1.324062] Movable zone start for each node
[    1.324452] Early memory node ranges
[    1.324782]   node   0: [mem 0x0000000000200000-0x00000000083fffff]
[    1.325363]   node   0: [mem 0x0000000009400000-0x00000000efffffff]
[    1.325946]   node   0: [mem 0x0000000100000000-0x00000001ffffffff]
[    1.326527] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[    1.372641] cma: Reserved 16 MiB at 0x00000000eec00000
[    1.373195] psci: probing for conduit method from DT.
[    1.373674] psci: PSCIv1.1 detected in firmware.
[    1.374101] psci: Using standard PSCI v0.2 function IDs
[    1.374590] psci: Trusted OS migration not required
[    1.375038] psci: SMC Calling Convention v1.2
[    1.375788] percpu: Embedded 30 pages/cpu s83480 r8192 d31208 u122880
[    1.376513] Detected VIPT I-cache on CPU0
[    1.376927] CPU features: detected: GIC system register CPU interface
[    1.377520] CPU features: detected: Virtualization Host Extensions
[    1.378093] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    1.378739] alternatives: patching kernel code
[    1.381229] Built 1 zonelists, mobility grouping on.  Total pages: 1995336
[    1.381870] Kernel command line: storagemedia=emmc androidboot.storagemedia=emmc androidboot.mode=normal  androidboot.verifiedbootstate=orange lycon=uart8250,mmio32,0xfe660000 console=ttyFIQ0 root=PARTUUID=614e0000-0000
[    1.385955] Dentry cache hash table entries: 1048576 (order: 11, 8388608 bytes, linear)
[    1.387663] Inode-cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    1.388383] mem auto-init: stack:off, heap alloc:off, heap free:off
[    1.404761] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[    1.499139] Memory: 7830248K/8108032K available (18304K kernel code, 3358K rwdata, 6076K rodata, 9600K init, 530K bss, 261400K reserved, 16384K
[    1.500556] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    1.501186] ftrace: allocating 56789 entries in 222 pages
[    1.585529] ftrace: allocated 222 pages with 6 groups
[    1.586298] rcu: Hierarchical RCU implementation.
[    1.586734] rcu:     RCU event tracing is enabled.
[    1.587150] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    1.587746]  Rude variant of Tasks RCU enabled.
[    1.588157] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    1.588847] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    1.594316] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    1.596230] GICv3: GIC: Using split EOI/Deactivate mode
[    1.596719] GICv3: 320 SPIs implemented
[    1.597070] GICv3: 0 Extended SPIs implemented
[    1.597511] GICv3: Distributor has no Range Selector support
[    1.598033] GICv3: 16 PPIs implemented
[    1.598413] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[    1.599158] ITS [mem 0xfd440000-0xfd45ffff]
[    1.599612] ITS@0x00000000fd440000: allocated 8192 Devices @2810000 (indirect, esz 8, psz 64K, shr 0)
[    1.600479] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @2820000 (flat, esz 2, psz 64K, shr 0)
[    1.601405] ITS: using cache flushing for cmd queue
[    1.602159] GICv3: using LPI property table @0x0000000002830000
[    1.602811] GIC: using cache flushing for LPI property table
[    1.603329] GICv3: CPU0: using allocated LPI pending table @0x0000000002840000
[    1.635717] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    1.636283] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    1.637267] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    1.638972] Console: colour dummy device 80x25
[    1.639411] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    1.640347] pid_max: default: 32768 minimum: 301
[    1.640919] Mount-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.641646] Mountpoint-cache hash table entries: 16384 (order: 5, 131072 bytes, linear)
[    1.643900] rcu: Hierarchical SRCU implementation.
[    1.645075] Platform MSI: interrupt-controller@fd440000 domain created
[    1.646100] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[    1.647176] EFI services will not be available.
[    1.647904] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[    1.649636] Detected VIPT I-cache on CPU1
[    1.649669] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[    1.649689] GICv3: CPU1: using allocated LPI pending table @0x0000000002850000
[    1.649740] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    1.651119] Detected VIPT I-cache on CPU2
[    1.651143] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[    1.651159] GICv3: CPU2: using allocated LPI pending table @0x0000000002860000
[    1.651196] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    1.652528] Detected VIPT I-cache on CPU3
[    1.652550] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[    1.652566] GICv3: CPU3: using allocated LPI pending table @0x0000000002870000
[    1.652601] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[    1.652704] smp: Brought up 1 node, 4 CPUs
[    1.659832] SMP: Total of 4 processors activated.
[    1.660272] CPU features: detected: Privileged Access Never
[    1.660779] CPU features: detected: User Access Override
[    1.661262] CPU features: detected: 32-bit EL0 Support
[    1.661728] CPU features: detected: Common not Private translations
[    1.662297] CPU features: detected: RAS Extension Support
[    1.662788] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    1.663566] CPU features: detected: CRC32 instructions
[    1.664041] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    1.664673] CPU features: detected: RCpc load-acquire (LDAPR)
[    1.665268] CPU: All CPU(s) started at EL2
[    1.667420] devtmpfs: initialized
[    1.683311] Registered cp15_barrier emulation handler
[    1.683791] Registered setend emulation handler
[    1.684395] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    1.685287] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    1.686445] pinctrl core: initialized pinctrl subsystem
[    1.687489] DMI not present or invalid.
[    1.688329] NET: Registered protocol family 16
[    1.690341] DMA: preallocated 1024 KiB GFP_KERNEL pool for atomic allocations
[    1.691222] DMA: preallocated 1024 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    1.693969] Registered FIQ tty driver
[    1.694655] thermal_sys: Registered thermal governor 'fair_share'
[    1.694660] thermal_sys: Registered thermal governor 'step_wise'
[    1.695216] thermal_sys: Registered thermal governor 'user_space'
[    1.695765] thermal_sys: Registered thermal governor 'power_allocator'
[    1.696592] thermal thermal_zone1: power_allocator: sustainable_power will be estimated
[    1.697980] cpuidle: using governor menu
[    1.698603] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    1.699349] ASID allocator initialised with 65536 entries
[    1.702094] ramoops: dmesg-0 0x20000@0x0000000000110000
[    1.702595] ramoops: console 0x80000@0x0000000000130000
[    1.703090] ramoops: pmsg    0x50000@0x00000000001b0000
[    1.703933] printk: console [ramoops-1] enabled
[    1.704347] pstore: Registered ramoops as persistent store backend
[    1.704930] ramoops: using 0xf0000@0x110000, ecc: 0
[    1.743127] rockchip-gpio fdd60000.gpio0: probed /pinctrl/gpio0@fdd60000
[    1.744246] rockchip-gpio fe740000.gpio1: probed /pinctrl/gpio1@fe740000
[    1.745515] rockchip-gpio fe750000.gpio2: probed /pinctrl/gpio2@fe750000
[    1.746682] rockchip-gpio fe760000.gpio3: probed /pinctrl/gpio3@fe760000
[    1.747820] rockchip-gpio fe770000.gpio4: probed /pinctrl/gpio4@fe770000
[    1.748523] rockchip-pinctrl pinctrl: probed pinctrl
[    1.773687] fiq_debugger fiq_debugger.0: IRQ fiq not found
[    1.774213] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[    1.774744] fiq_debugger_probe: could not install nmi irq handler