U-Boot 2017.09-gb2f1de7c96-dirty #xu_yuntong (May 12 2022 - 16:08:39 +0800)

Model: Rockchip RK3568 Evaluation Board
PreSerial: 2, raw, 0xfe660000
DRAM:  4 GiB
Sysmem: init
Relocation Offset: ed34b000
Relocation fdt: eb9f8ce8 - eb9fece0
CR: M/C/I
Using default environment

dwmmc@fe2b0000: 1, dwmmc@fe2c0000: 2, sdhci@fe310000: 0
Bootdev(atags): mmc 0
MMC0: HS200, 200Mhz
PartType: EFI
DM: v1
boot mode: normal
FIT: No boot partition
105968 bytes read in 15 ms (6.7 MiB/s)
DTB(Distro): /extlinux/toybrick.dtb
I2c0 speed: 100000Hz
vsel-gpios- not found! Error: -2
vdd_cpu init 900000 uV
PMIC:  RK8090 (on=0x40, off=0x00)
vdd_logic init 900000 uV
vdd_gpu init 900000 uV
vdd_npu init 900000 uV
io-domain: OK
Warn: can't find connect driver
Could not find baseparameter partition
Found DTB in resource part
Rockchip UBOOT DRM driver version: v1.0.1
VOP have 2 active VP
vp0 have layer nr:3[1 3 5 ], primary plane: 5
vp1 have layer nr:3[0 2 4 ], primary plane: 4
vp2 have layer nr:0[], primary plane: 0
Using display timing dts
dsi@fe070000:  detailed mode clock 65000 kHz, flags[8000000a]
    H: 1024 1184 1194 1354
    V: 0600 0612 0613 0636
bus_format: 100e
VOP update mode to: 1024x600p0, type: MIPI1 for VP1
VOP VP1 enable Smart0[1280x720->1024x600@0x0] fmt[1] addr[0xee1a4000]
final DSI-Link bandwidth: 432 Mbps x 4
xfer: num: 2, addr: 0x50
xfer: num: 2, addr: 0x50
Monitor has basic audio support
Could not find baseparameter partition
mode:1920x1080
hdmi@fe0a0000:  detailed mode clock 148500 kHz, flags[5]
    H: 1920 2008 2052 2200
    V: 1080 1084 1089 1125
bus_format: 2025
VOP update mode to: 1920x1080p0, type: HDMI0 for VP0
VOP VP0 enable Smart1[1280x720->1280x720@320x180] fmt[1] addr[0xee1a4000]
CEA mode used vic=16
final pixclk = 148500000 tmdsclk = 148500000
PHY powered down in 0 iterations
PHY PLL locked 1 iterations
PHY powered down in 0 iterations
PHY PLL locked 1 iterations
sink has audio support
hdmi_set_clk_regenerator: fs=48000Hz ftdms=148.500MHz N=6144 cts=148500
CLK: (sync kernel. arm: enter 816000 KHz, init 816000 KHz, kernel 0N/A)
  apll 1416000 KHz
  dpll 780000 KHz
  gpll 1188000 KHz
  cpll 1000000 KHz
  npll 1200000 KHz
  vpll 650000 KHz
  hpll 148000 KHz
  ppll 200000 KHz
  armclk 1416000 KHz
  aclk_bus 150000 KHz
  pclk_bus 100000 KHz
  aclk_top_high 500000 KHz
  aclk_top_low 400000 KHz
  hclk_top 150000 KHz
  pclk_top 100000 KHz
  aclk_perimid 300000 KHz
  hclk_perimid 150000 KHz
  pclk_pmu 100000 KHz
Net:   eth1: ethernet@fe010000, eth0: ethernet@fe2a0000
Hit key to stop autoboot('CTRL+C'):  0 
ANDROID: reboot reason: "(none)"
optee api revision: 2.0
TEEC: Waring: Could not find security partition
Not AVB images, AVB skip
android_image_load_by_partname: Can't find part: boot
Android image load failed
Android boot failed, error -1.
## Booting FIT Image FIT: No boot partition
FIT: No fit blob
FIT: No FIT image
Could not find userdata part
MMC error: The cmd index is 1, ret is -110.....
Card did not respond to voltage select!
mmc_init: -95, time 12
switch to partitions #0, OK
mmc0(part 0) is current device
Scanning mmc 0:4...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
203 bytes read in 5 ms (39.1 KiB/s)
1:      rockchip-kernel-5.10
Load from partition ' ramdisk ' to address 0xa200000, count: 8192 block(s)
Read from partition ' ramdisk ' done, total block(s) 8192
Openharmony ramdisk_addr_r = 0x0a200000:0x400000
Retrieving file: /extlinux/Image
27484168 bytes read in 213 ms (123.1 MiB/s)
append: earlycon=uart8250,mmio32,0xfe660000 root=PARTUUID=614e0000-0000-4b53-8000-1d28000054a9 rw rootwait rootfstype=ext4
Retrieving file: /extlinux/toybrick.dtb
105968 bytes read in 20 ms (5.1 MiB/s)
Fdt Ramdisk skip relocation
## Flattened Device Tree blob at 0x0a100000
   Booting using the fdt blob at 0x0a100000
  'reserved-memory' ramoops@110000: addr=110000 size=f0000
   Using Device Tree in place at 000000000a100000, end 000000000a11cdef
vp0, plane_mask:0x2a, primary-id:5, curser-id:-1
vp1, plane_mask:0x15, primary-id:4, curser-id:-1
vp2, plane_mask:0x0, primary-id:0, curser-id:-1
Adding bank: 0x00200000 - 0x08400000 (size: 0x08200000)
Adding bank: 0x09400000 - 0xf0000000 (size: 0xe6c00000)
Adding bank: 0x1f0000000 - 0x200000000 (size: 0x10000000)
Total: 1206.764 ms

Starting kernel ...

[    0.000000] Booting Linux on physical CPU 0x0000000000 [0x412fd050]
[    0.000000] Linux version 5.10.97 (samfei@newbridge-To-be-filled-by-O-E-M) (OHOS (dev) clang version 12.0.1 (llvm-project 1971c85d809b8dd102ede1ec71208518a9b0f68e), LLD 12.0.1 (https://gitee.com/OpenHarmony/third_party_llvm-project 1971c85d809b8dd102ede1ec71208518a9b0f68e)) #1 SMP Thu Jan 11 15:03:57 CST 2024
[    0.000000] Machine model: rockchip,rk3568-toybrick-dev-linux-x0
[    0.000000] earlycon: uart8250 at MMIO32 0x00000000fe660000 (options '')
[    0.000000] printk: bootconsole [uart8250] enabled
[    0.000000] Zone ranges:
[    0.000000]   DMA      [mem 0x0000000000200000-0x00000000ffffffff]
[    0.000000]   DMA32    empty
[    0.000000]   Normal   [mem 0x0000000100000000-0x00000001ffffffff]
[    0.000000] Movable zone start for each node
[    0.000000] Early memory node ranges
[    0.000000]   node   0: [mem 0x0000000000200000-0x00000000083fffff]
[    0.000000]   node   0: [mem 0x0000000009400000-0x00000000efffffff]
[    0.000000]   node   0: [mem 0x00000001f0000000-0x00000001ffffffff]
[    0.000000] Initmem setup node 0 [mem 0x0000000000200000-0x00000001ffffffff]
[    0.000000] cma: Reserved 16 MiB at 0x00000000eec00000
[    0.000000] psci: probing for conduit method from DT.
[    0.000000] psci: PSCIv1.1 detected in firmware.
[    0.000000] psci: Using standard PSCI v0.2 function IDs
[    0.000000] psci: Trusted OS migration not required
[    0.000000] psci: SMC Calling Convention v1.2
[    0.000000] percpu: Embedded 30 pages/cpu s83880 r8192 d30808 u122880
[    0.000000] Detected VIPT I-cache on CPU0
[    0.000000] CPU features: detected: GIC system register CPU interface
[    0.000000] CPU features: detected: Virtualization Host Extensions
[    0.000000] CPU features: detected: ARM errata 1165522, 1319367, or 1530923
[    0.000000] alternatives: patching kernel code
[    0.000000] Built 1 zonelists, mobility grouping on.  Total pages: 1027656
[    0.000000] Kernel command line: earlycon=uart8250,mmio32,0xfe660000 root=PARTUUID=614e0000-0000 rw rootwait rootfstype=ext4 console=ttyFIQ0 hardware=rk3568 default_boot_device=fe310000.sdhci bootslots=2 ohos.required_mount.system=/dev/block/platform/fe310000.sdhci/by-name/system@/usr@ext4@ro,barrier=1@wait,required ohos.required_mount.vendor=/dev/block/platform/fe310000.sdhci/by-name/vendor@/vendor@ext4@ro,barrier=1@wait,required ohos.required_mount.misc=/dev/block/platform/fe310000.sdhci/by-name/misc@none@none@none@wait,required
[    0.000000] Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes, linear)
[    0.000000] Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes, linear)
[    0.000000] mem auto-init: stack:off, heap alloc:on, heap free:off
[    0.000000] software IO TLB: mapped [mem 0x00000000e9f00000-0x00000000edf00000] (64MB)
[    0.000000] Memory: 3953532K/4175872K available (16574K kernel code, 3352K rwdata, 5348K rodata, 1536K init, 884K bss, 205956K reserved, 16384K cma-reserved)
[    0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1
[    0.000000] ftrace: allocating 56613 entries in 222 pages
[    0.000000] ftrace: allocated 222 pages with 6 groups
[    0.000000] rcu: Hierarchical RCU implementation.
[    0.000000] rcu:     RCU event tracing is enabled.
[    0.000000] rcu:     RCU restricting CPUs from NR_CPUS=8 to nr_cpu_ids=4.
[    0.000000]  Rude variant of Tasks RCU enabled.
[    0.000000] rcu: RCU calculated value of scheduler-enlistment delay is 30 jiffies.
[    0.000000] rcu: Adjusting geometry for rcu_fanout_leaf=16, nr_cpu_ids=4
[    0.000000] NR_IRQS: 64, nr_irqs: 64, preallocated irqs: 0
[    0.000000] GICv3: GIC: Using split EOI/Deactivate mode
[    0.000000] GICv3: 320 SPIs implemented
[    0.000000] GICv3: 0 Extended SPIs implemented
[    0.000000] GICv3: Distributor has no Range Selector support
[    0.000000] GICv3: 16 PPIs implemented
[    0.000000] GICv3: CPU0: found redistributor 0 region 0:0x00000000fd460000
[    0.000000] ITS [mem 0xfd440000-0xfd45ffff]
[    0.000000] ITS@0x00000000fd440000: allocated 8192 Devices @210000 (indirect, esz 8, psz 64K, shr 0)
[    0.000000] ITS@0x00000000fd440000: allocated 32768 Interrupt Collections @220000 (flat, esz 2, psz 64K, shr 0)
[    0.000000] ITS: using cache flushing for cmd queue
[    0.000000] GICv3: using LPI property table @0x0000000000230000
[    0.000000] GIC: using cache flushing for LPI property table
[    0.000000] GICv3: CPU0: using allocated LPI pending table @0x0000000000240000
[    0.000000] random: get_random_bytes called from start_kernel+0x200/0x44c with crng_init=0
[    0.000000] arch_timer: cp15 timer(s) running at 24.00MHz (phys).
[    0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0x588fe9dc0, max_idle_ns: 440795202592 ns
[    0.000004] sched_clock: 56 bits at 24MHz, resolution 41ns, wraps every 4398046511097ns
[    0.001598] Console: colour dummy device 80x25
[    0.002039] Calibrating delay loop (skipped), value calculated using timer frequency.. 48.00 BogoMIPS (lpj=80000)
[    0.002985] pid_max: default: 32768 minimum: 301
[    0.003491] LSM: Security Framework initializing
[    0.003949] SELinux:  Initializing.
[    0.004370] Mount-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.005086] Mountpoint-cache hash table entries: 8192 (order: 4, 65536 bytes, linear)
[    0.007507] rcu: Hierarchical SRCU implementation.
[    0.008769] Platform MSI: interrupt-controller@fd440000 domain created
[    0.009720] PCI/MSI: /interrupt-controller@fd400000/interrupt-controller@fd440000 domain created
[    0.011097] smp: Bringing up secondary CPUs ...
I/TC: Secondary CPU 1 initializing
I/TC: Secondary CPU 1 switching to normal world boot
I/TC: Secondary CPU 2 initializing
I/TC: Secondary CPU 2 switching to normal world boot
I/TC: Secondary CPU 3 initializing
I/TC: Secondary CPU 3 switching to normal world boot
[    0.012873] Detected VIPT I-cache on CPU1
[    0.012902] GICv3: CPU1: found redistributor 100 region 0:0x00000000fd480000
[    0.012922] GICv3: CPU1: using allocated LPI pending table @0x0000000000250000
[    0.012976] CPU1: Booted secondary processor 0x0000000100 [0x412fd050]
[    0.014389] Detected VIPT I-cache on CPU2
[    0.014414] GICv3: CPU2: found redistributor 200 region 0:0x00000000fd4a0000
[    0.014431] GICv3: CPU2: using allocated LPI pending table @0x0000000000260000
[    0.014473] CPU2: Booted secondary processor 0x0000000200 [0x412fd050]
[    0.015888] Detected VIPT I-cache on CPU3
[    0.015913] GICv3: CPU3: found redistributor 300 region 0:0x00000000fd4c0000
[    0.015929] GICv3: CPU3: using allocated LPI pending table @0x0000000000270000
[    0.015970] CPU3: Booted secondary processor 0x0000000300 [0x412fd050]
[    0.016121] smp: Brought up 1 node, 4 CPUs
[    0.023327] SMP: Total of 4 processors activated.
[    0.023761] CPU features: detected: Privileged Access Never
[    0.024273] CPU features: detected: User Access Override
[    0.024760] CPU features: detected: 32-bit EL0 Support
[    0.025232] CPU features: detected: Common not Private translations
[    0.025827] CPU features: detected: RAS Extension Support
[    0.026324] CPU features: detected: Data cache clean to the PoU not required for I/D coherence
[    0.027113] CPU features: detected: CRC32 instructions
[    0.027584] CPU features: detected: Speculative Store Bypassing Safe (SSBS)
[    0.028311] CPU: All CPU(s) started at EL2
[    0.030197] devtmpfs: initialized
[    0.047163] Registered cp15_barrier emulation handler
[    0.047648] Registered setend emulation handler
[    0.048070] KASLR disabled due to lack of seed
[    0.048751] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 6370867519511994 ns
[    0.049730] futex hash table entries: 1024 (order: 4, 65536 bytes, linear)
[    0.050963] pinctrl core: initialized pinctrl subsystem
[    0.052322] bbox:[info][blackbox_core.c:262] wait for log part [/data] begin!
[    0.052596] NET: Registered protocol family 16
[    0.054841] DMA: preallocated 512 KiB GFP_KERNEL pool for atomic allocations
[    0.055598] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA pool for atomic allocations
[    0.056493] DMA: preallocated 512 KiB GFP_KERNEL|GFP_DMA32 pool for atomic allocations
[    0.057297] audit: initializing netlink subsys (disabled)
[    0.058003] audit: type=2000 audit(0.056:1): state=initialized audit_enabled=0 res=1
[    0.059936] thermal_sys: Registered thermal governor 'fair_share'
[    0.059942] thermal_sys: Registered thermal governor 'step_wise'
[    0.061066] cpuidle: using governor menu
[    0.062005] Registered FIQ tty driver
[    0.062391] bbox:[info][blackbox_core.c:514] [SYSTEM] is registered successfully!
[    0.063781] hw-breakpoint: found 6 breakpoint and 4 watchpoint registers.
[    0.064543] ASID allocator initialised with 65536 entries
[    0.070596] printk: console [ramoops-1] enabled
[    0.071019] pstore: Registered ramoops as persistent store backend
[    0.071587] ramoops: using 0xf0000@0x110000, ecc: 0
[    0.116496] rockchip-gpio fdd60000.gpio0: probed gpio0 (fdd60000.gpio0)
[    0.119468] rockchip-gpio fe740000.gpio1: probed gpio1 (fe740000.gpio1)
[    0.122477] rockchip-gpio fe750000.gpio2: probed gpio2 (fe750000.gpio2)
[    0.125372] rockchip-gpio fe760000.gpio3: probed gpio3 (fe760000.gpio3)
[    0.127729] rockchip-gpio fe770000.gpio4: probed gpio4 (fe770000.gpio4)
[    0.128423] rockchip-pinctrl pinctrl: probed pinctrl
[    0.141991] cryptd: max_cpu_qlen set to 1000
[    0.146937] fiq_debugger fiq_debugger.0: IRQ fiq not found
[    0.147474] fiq_debugger fiq_debugger.0: IRQ wakeup not found
[[    0.148140] printk: console [ttyFIQ0] enabled
    0.148140] printk: console [ttyFIQ0] enabled
[    0.148934] printk: bootconsole [uart8250] disabled
[    0.148934] printk: bootconsole [uart8250] disabled
[    0.149655] Registered fiq debugger ttyFIQ0
[    0.150874] vcc3v3_sys: supplied by dc_12v
[    0.151308] vcc5v0_sys: supplied by dc_12v
[    0.153085] vcc2v5-sys: supplied by vcc3v3_sys
[    0.153483] pcie30_avdd0v9: supplied by vcc3v3_sys
[    0.153870] pcie30_avdd1v8: supplied by vcc3v3_sys
[    0.154394] vcc3v3_pcie: supplied by vcc5v0_sys
[    0.155219] vcc3v3_bu: supplied by vcc5v0_sys
[    0.156938] iommu: Default domain type: Translated 
[    0.157195] rk_iommu fdea0800.iommu: version = 2
[    0.157772] rk_iommu fded0480.iommu: version = 2
[    0.158083] rk_iommu fdee0800.iommu: version = 2
[    0.158413] rk_iommu fdef0800.iommu: version = 2
[    0.158693] rk_iommu fdf40f00.iommu: version = 2
[    0.159026] rk_iommu fdf80800.iommu: version = 2
[    0.159310] rk_iommu fdff1a00.iommu: version = 2
[    0.159573] rk_iommu fe043e00.iommu: version = 2
[    0.160454] SCSI subsystem initialized
[    0.160689] usbcore: registered new interface driver usbfs
[    0.160744] usbcore: registered new interface driver hub
[    0.160795] usbcore: registered new device driver usb
[    0.160864] mc: Linux media interface: v0.10
[    0.160898] videodev: Linux video capture interface: v2.00
[    0.160993] pps_core: LinuxPPS API ver. 1 registered
[    0.161004] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>
[    0.161023] PTP clock support registered
[    0.161816] arm-scmi firmware:scmi: SCMI Notifications - Core Enabled.
[    0.161877] arm-scmi firmware:scmi: SCMI Protocol v2.0 'rockchip:' Firmware version 0x0
[    0.163816] Advanced Linux Sound Architecture Driver Initialized.
[    0.164292] Bluetooth: Core ver 2.22
[    0.164338] NET: Registered protocol family 31
[    0.164347] Bluetooth: HCI device and connection manager initialized
[    0.164362] Bluetooth: HCI socket layer initialized
[    0.164373] Bluetooth: L2CAP socket layer initialized
[    0.164395] Bluetooth: SCO socket layer initialized
[    0.164792] rockchip-cpuinfo cpuinfo: failed to get id cell: -517
[    0.165848] clocksource: Switched to clocksource arch_sys_counter
[    0.579884] VFS: Disk quotas dquot_6.6.0
[    0.579992] VFS: Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[    0.589468] NET: Registered protocol family 2
[    0.589712] IP idents hash table entries: 65536 (order: 7, 524288 bytes, linear)
[    0.591823] tcp_listen_portaddr_hash hash table entries: 2048 (order: 4, 81920 bytes, linear)
[    0.591991] TCP established hash table entries: 32768 (order: 6, 262144 bytes, linear)
[    0.592371] TCP bind hash table entries: 32768 (order: 8, 1048576 bytes, linear)
[    0.593190] TCP: Hash tables configured (established 32768 bind 32768)
[    0.593538] UDP hash table entries: 2048 (order: 5, 196608 bytes, linear)
[    0.593778] UDP-Lite hash table entries: 2048 (order: 5, 196608 bytes, linear)
[    0.594112] NET: Registered protocol family 1
[    0.594753] RPC: Registered named UNIX socket transport module.
[    0.594764] RPC: Registered udp transport module.
[    0.594771] RPC: Registered tcp transport module.
[    0.594778] RPC: Registered tcp NFSv4.1 backchannel transport module.
[    0.595732] PCI: CLS 0 bytes, default 64
[    0.596527] Trying to unpack rootfs image as initramfs...
[    0.726835] rootfs image is not initramfs (read error); looks like an initrd
[    0.735582] Freeing initrd memory: 4096K
[    0.736846] hw perfevents: enabled with armv8_cortex_a55 PMU driver, 7 counters available
[    0.742937] Initialise system trusted keyrings
[    0.743210] workingset: timestamp_bits=46 max_order=20 bucket_order=0
[    0.749751]  hmdfs: hmdfs_init_configfs() init configfs
[    0.749879] Registering sharefs
[    0.749961]  sharefs: sharefs_init_configfs() init configfs
[    0.750218] squashfs: version 4.0 (2009/01/31) Phillip Lougher
[    0.751162] NFS: Registering the id_resolver key type
[    0.751202] Key type id_resolver registered
[    0.751211] Key type id_legacy registered
[    0.751251] ntfs: driver 2.1.32 [Flags: R/O].
[    0.751419] jffs2: version 2.2. (NAND) © 2001-2006 Red Hat, Inc.
[    0.751792] fuse: init (API version 7.32)
[    0.752186] SGI XFS with security attributes, no debug enabled
[    0.780899] NET: Registered protocol family 38
[    0.780941] Key type asymmetric registered
[    0.780952] Asymmetric key parser 'x509' registered
[    0.781011] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 242)
[    0.781023] io scheduler mq-deadline registered
[    0.781031] io scheduler kyber registered
[    0.781769] rockchip-csi2-dphy-hw fe870000.csi2-dphy-hw: csi2 dphy hw probe successfully!
[    0.782463] rockchip-csi2-dphy csi2-dphy0: csi2 dphy0 probe successfully!
[    0.795150] rk-pcie 3c0000000.pcie: no vpcie3v3 regulator found
[    0.795479] rk-pcie 3c0000000.pcie: missing legacy IRQ resource
[    0.795498] rk-pcie 3c0000000.pcie: Missing *config* reg space
[    0.795517] rk-pcie 3c0000000.pcie: host bridge /pcie@fe260000 ranges:
[    0.795547] rk-pcie 3c0000000.pcie:      err 0x00f4000000..0x00f40fffff -> 0x00f4000000
[    0.795565] rk-pcie 3c0000000.pcie:       IO 0x00f4100000..0x00f41fffff -> 0x00f4100000
[    0.795584] rk-pcie 3c0000000.pcie:      MEM 0x00f4200000..0x00f5ffffff -> 0x00f4200000
[    0.795598] rk-pcie 3c0000000.pcie:      MEM 0x0300000000..0x033fffffff -> 0x0300000000
[    0.795638] rk-pcie 3c0000000.pcie: Missing *config* reg space
[    0.795672] rk-pcie 3c0000000.pcie: invalid resource
[    0.796628] pwm-backlight backlight: supply power not found, using dummy regulator
[    0.797155] pwm-backlight backlight1: supply power not found, using dummy regulator
[    0.797827] mpp_service mpp-srv: unknown mpp version for missing VCS info
[    0.797839] mpp_service mpp-srv: probe start
[    0.799586] mpp_rkvenc fdf40000.rkvenc: Adding to iommu group 4
[    0.799851] mpp_rkvenc fdf40000.rkvenc: probing start
[    0.800195] mpp_rkvenc fdf40000.rkvenc: venc regulator not ready, retry
[    0.800210] rkvenc_init:1203: failed to add venc devfreq
[    0.800588] mpp_rkvenc fdf40000.rkvenc: probing finish
[    0.801904] mpp_vdpu2 fdea0400.vdpu: Adding to iommu group 0
[    0.802108] mpp_vdpu2 fdea0400.vdpu: probe device
[    0.802618] mpp_vdpu2 fdea0400.vdpu: probing finish
[    0.803305] mpp_vepu2 fdee0000.vepu: Adding to iommu group 2
[    0.803510] mpp_vepu2 fdee0000.vepu: probing start
[    0.803994] mpp_vepu2 fdee0000.vepu: probing finish
[    0.804663] mpp-iep2 fdef0000.iep: Adding to iommu group 3
[    0.804821] mpp-iep2 fdef0000.iep: probe device
[    0.805124] mpp-iep2 fdef0000.iep: allocate roi buffer failed
[    0.805327] mpp-iep2 fdef0000.iep: probing finish
[    0.806003] mpp_jpgdec fded0000.jpegd: Adding to iommu group 1
[    0.806162] mpp_jpgdec fded0000.jpegd: probe device
[    0.806633] mpp_jpgdec fded0000.jpegd: probing finish
[    0.807354] mpp_rkvdec2 fdf80200.rkvdec: Adding to iommu group 5
[    0.807596] mpp_rkvdec2 fdf80200.rkvdec: rkvdec, probing start
[    0.807944] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_a is not found!
[    0.807958] rkvdec2_init:687: No niu aclk reset resource define
[    0.807969] mpp_rkvdec2 fdf80200.rkvdec: shared_niu_h is not found!
[    0.807976] rkvdec2_init:690: No niu hclk reset resource define
[    0.808144] mpp_rkvdec2 fdf80200.rkvdec: sram_start 0x00000000fdcc0000
[    0.808155] mpp_rkvdec2 fdf80200.rkvdec: rcb_iova 0x0000000010000000
[    0.808163] mpp_rkvdec2 fdf80200.rkvdec: sram_size 45056
[    0.808171] mpp_rkvdec2 fdf80200.rkvdec: rcb_size 65536
[    0.808180] mpp_rkvdec2 fdf80200.rkvdec: min_width 512
[    0.808192] mpp_rkvdec2 fdf80200.rkvdec: link mode resource not found
[    0.808418] mpp_rkvdec2 fdf80200.rkvdec: probing finish
[    0.809260] mpp_service mpp-srv: probe success
[    0.815148] dma-pl330 fe530000.dmac: Loaded driver for PL330 DMAC-241330
[    0.815173] dma-pl330 fe530000.dmac:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    0.817295] dma-pl330 fe550000.dmac: Loaded driver for PL330 DMAC-241330
[    0.817316] dma-pl330 fe550000.dmac:         DBUFF-128x8bytes Num_Chans-8 Num_Peri-32 Num_Events-16
[    0.818747] rockchip-pvtm fde00000.pvtm: pvtm@0 probed
[    0.818904] rockchip-pvtm fde80000.pvtm: pvtm@1 probed
[    0.819027] rockchip-pvtm fde90000.pvtm: pvtm@2 probed
[    0.819996] rockchip-system-monitor rockchip-system-monitor: system monitor probe
[    0.821056] Serial: 8250/16550 driver, 10 ports, IRQ sharing disabled
[    0.821877] fe670000.serial: ttyS3 at MMIO 0xfe670000 (irq = 77, base_baud = 1500000) is a 16550A
[    0.822800] fe680000.serial: ttyS4 at MMIO 0xfe680000 (irq = 78, base_baud = 1500000) is a 16550A
[    0.823587] fe6c0000.serial: ttyS8 at MMIO 0xfe6c0000 (irq = 79, base_baud = 1500000) is a 16550A
[    0.826451] rockchip-vop2 fe040000.vop: Adding to iommu group 7
[    0.834285] no ATF memory for init
[    0.838708] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp0 assign plane mask: 0x2a, primary plane phy id: 5
[    0.838770] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp1 assign plane mask: 0x15, primary plane phy id: 4
[    0.838786] rockchip-vop2 fe040000.vop: [drm:vop2_bind] vp2 assign plane mask: 0x0, primary plane phy id: -1
[    0.839003] [drm] failed to init overlay plane Cluster0-win0
[    0.839013] [drm] failed to init overlay plane Cluster0-win1
[    0.839020] [drm] failed to init overlay plane Cluster1-win0
[    0.839027] [drm] failed to init overlay plane Cluster1-win1
[    0.839208] rockchip-drm display-subsystem: bound fe040000.vop (ops 0xffffffc011125cc8)
[    0.839707] dwhdmi-rockchip fe0a0000.hdmi: Detected HDMI TX controller v2.11a with HDCP (DWC HDMI 2.0 TX PHY)
[    0.840300] dwhdmi-rockchip fe0a0000.hdmi: registered DesignWare HDMI I2C bus driver
[    0.840962] rockchip-drm display-subsystem: bound fe0a0000.hdmi (ops 0xffffffc01112f038)
[    0.841086] rockchip-drm display-subsystem: bound fe070000.dsi (ops 0xffffffc0111302e0)
[    0.841613] get_framebuffer_by_node: failed to get logo,offset
[    0.948023] random: fast init done
[    1.104591] rockchip-drm display-subsystem: [drm] fb0: rockchipdrmfb frame buffer device
[    1.105644] [drm] Initialized rockchip 3.0.0 20140818 for display-subsystem on minor 0
[    1.107721] mali fde60000.gpu: Kernel DDK version g2p0-01eac0
[    1.107840] mali fde60000.gpu: Power management initialization failed error = -517
[    1.107864] mali fde60000.gpu: Device initialization Deferred
[    1.108432] cacheinfo: Unable to detect cache hierarchy for CPU 0
[    1.109146] brd: module loaded
[    1.115568] loop: module loaded
[    1.116124] zram: Added device: zram0
[    1.116436] lkdtm: No crash points registered, enable through debugfs
[    1.120073] tun: Universal TUN/TAP device driver, 1.6
[    1.120294] CAN device driver interface
[    1.123429] rk_gmac-dwmac fe010000.ethernet: IRQ eth_lpi not found
[    1.123716] rk_gmac-dwmac fe010000.ethernet: no regulator found
[    1.123731] rk_gmac-dwmac fe010000.ethernet: clock input or output? (output).
[    1.123742] rk_gmac-dwmac fe010000.ethernet: TX delay(0x37).
[    1.123751] rk_gmac-dwmac fe010000.ethernet: RX delay(0xf).
[    1.123766] rk_gmac-dwmac fe010000.ethernet: integrated PHY? (no).
[    1.124038] rk_gmac-dwmac fe010000.ethernet: init for RGMII
[    1.124277] rk_gmac-dwmac fe010000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[    1.124292] rk_gmac-dwmac fe010000.ethernet:         DWMAC4/5
[    1.124304] rk_gmac-dwmac fe010000.ethernet: DMA HW capability register supported
[    1.124313] rk_gmac-dwmac fe010000.ethernet: RX Checksum Offload Engine supported
[    1.124320] rk_gmac-dwmac fe010000.ethernet: TX Checksum insertion supported
[    1.124328] rk_gmac-dwmac fe010000.ethernet: Wake-Up On Lan supported
[    1.124401] rk_gmac-dwmac fe010000.ethernet: TSO supported
[    1.124412] rk_gmac-dwmac fe010000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.124421] rk_gmac-dwmac fe010000.ethernet: TSO feature enabled
[    1.124430] rk_gmac-dwmac fe010000.ethernet: Using 32 bits DMA width
[    1.259551] rk_gmac-dwmac fe2a0000.ethernet: IRQ eth_lpi not found
[    1.259857] rk_gmac-dwmac fe2a0000.ethernet: no regulator found
[    1.259872] rk_gmac-dwmac fe2a0000.ethernet: clock input or output? (output).
[    1.259883] rk_gmac-dwmac fe2a0000.ethernet: TX delay(0x2d).
[    1.259892] rk_gmac-dwmac fe2a0000.ethernet: RX delay(0x13).
[    1.259906] rk_gmac-dwmac fe2a0000.ethernet: integrated PHY? (no).
[    1.260188] rk_gmac-dwmac fe2a0000.ethernet: init for RGMII
[    1.260424] rk_gmac-dwmac fe2a0000.ethernet: User ID: 0x30, Synopsys ID: 0x51
[    1.260440] rk_gmac-dwmac fe2a0000.ethernet:         DWMAC4/5
[    1.260452] rk_gmac-dwmac fe2a0000.ethernet: DMA HW capability register supported
[    1.260460] rk_gmac-dwmac fe2a0000.ethernet: RX Checksum Offload Engine supported
[    1.260468] rk_gmac-dwmac fe2a0000.ethernet: TX Checksum insertion supported
[    1.260475] rk_gmac-dwmac fe2a0000.ethernet: Wake-Up On Lan supported
[    1.260543] rk_gmac-dwmac fe2a0000.ethernet: TSO supported
[    1.260553] rk_gmac-dwmac fe2a0000.ethernet: Enable RX Mitigation via HW Watchdog Timer
[    1.260562] rk_gmac-dwmac fe2a0000.ethernet: TSO feature enabled
[    1.260572] rk_gmac-dwmac fe2a0000.ethernet: Using 32 bits DMA width
[    1.396264] usbcore: registered new interface driver rndis_wlan
[    1.396348] usbcore: registered new interface driver rtl8150
[    1.396392] usbcore: registered new interface driver r8152
[    1.396444] usbcore: registered new interface driver asix
[    1.396485] usbcore: registered new interface driver ax88179_178a
[    1.396529] usbcore: registered new interface driver cdc_ether
[    1.396567] usbcore: registered new interface driver net1080
[    1.396609] usbcore: registered new interface driver rndis_host
[    1.396647] usbcore: registered new interface driver cdc_subset
[    1.396684] usbcore: registered new interface driver zaurus
[    1.396733] usbcore: registered new interface driver qmi_wwan_q
[    1.639723] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[    1.639770] ehci-pci: EHCI PCI platform driver
[    1.639847] ehci-platform: EHCI generic platform driver
[    1.640289] phy phy-fe8b0000.usb2-phy.4: illegal mode
[    1.642562] ehci-platform fd800000.usb: EHCI Host Controller
[    1.642792] ehci-platform fd800000.usb: new USB bus registered, assigned bus number 1
[    1.642927] ehci-platform fd800000.usb: irq 19, io mem 0xfd800000
[    1.655852] ehci-platform fd800000.usb: USB 2.0 started, EHCI 1.00
[    1.656115] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    1.656127] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.656136] usb usb1: Product: EHCI Host Controller
[    1.656145] usb usb1: Manufacturer: Linux 5.10.97 ehci_hcd
[    1.656153] usb usb1: SerialNumber: fd800000.usb
[    1.656663] hub 1-0:1.0: USB hub found
[    1.656710] hub 1-0:1.0: 1 port detected
[    1.659807] ehci-platform fd880000.usb: EHCI Host Controller
[    1.660071] ehci-platform fd880000.usb: new USB bus registered, assigned bus number 2
[    1.660204] ehci-platform fd880000.usb: irq 21, io mem 0xfd880000
[    1.672534] ehci-platform fd880000.usb: USB 2.0 started, EHCI 1.00
[    1.672804] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    1.672817] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.672826] usb usb2: Product: EHCI Host Controller
[    1.672834] usb usb2: Manufacturer: Linux 5.10.97 ehci_hcd
[    1.672842] usb usb2: SerialNumber: fd880000.usb
[    1.673314] hub 2-0:1.0: USB hub found
[    1.673359] hub 2-0:1.0: 1 port detected
[    1.674300] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[    1.674337] ohci-platform: OHCI generic platform driver
[    1.674661] phy phy-fe8b0000.usb2-phy.4: illegal mode
[    1.674679] ohci-platform fd840000.usb: Generic Platform OHCI controller
[    1.674891] ohci-platform fd840000.usb: new USB bus registered, assigned bus number 3
[    1.675015] ohci-platform fd840000.usb: irq 20, io mem 0xfd840000
[    1.733411] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    1.733434] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.733443] usb usb3: Product: Generic Platform OHCI controller
[    1.733452] usb usb3: Manufacturer: Linux 5.10.97 ohci_hcd
[    1.733459] usb usb3: SerialNumber: fd840000.usb
[    1.733935] hub 3-0:1.0: USB hub found
[    1.733981] hub 3-0:1.0: 1 port detected
[    1.734722] ohci-platform fd8c0000.usb: Generic Platform OHCI controller
[    1.734922] ohci-platform fd8c0000.usb: new USB bus registered, assigned bus number 4
[    1.735051] ohci-platform fd8c0000.usb: irq 22, io mem 0xfd8c0000
[    1.793424] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001, bcdDevice= 5.10
[    1.793458] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.793467] usb usb4: Product: Generic Platform OHCI controller
[    1.793475] usb usb4: Manufacturer: Linux 5.10.97 ohci_hcd
[    1.793483] usb usb4: SerialNumber: fd8c0000.usb
[    1.794006] hub 4-0:1.0: USB hub found
[    1.794053] hub 4-0:1.0: 1 port detected
[    1.796005] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    1.796240] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 5
[    1.796391] xhci-hcd xhci-hcd.3.auto: hcc params 0x0220fe64 hci version 0x110 quirks 0x0000000002010010
[    1.796453] xhci-hcd xhci-hcd.3.auto: irq 94, io mem 0xfd000000
[    1.796818] usb usb5: New USB device found, idVendor=1d6b, idProduct=0002, bcdDevice= 5.10
[    1.796831] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.796840] usb usb5: Product: xHCI Host Controller
[    1.796848] usb usb5: Manufacturer: Linux 5.10.97 xhci-hcd
[    1.796855] usb usb5: SerialNumber: xhci-hcd.3.auto
[    1.797331] hub 5-0:1.0: USB hub found
[    1.797378] hub 5-0:1.0: 1 port detected
[    1.797734] xhci-hcd xhci-hcd.3.auto: xHCI Host Controller
[    1.797913] xhci-hcd xhci-hcd.3.auto: new USB bus registered, assigned bus number 6
[    1.797933] xhci-hcd xhci-hcd.3.auto: Host supports USB 3.0 SuperSpeed
[    1.798019] usb usb6: We don't know the algorithms for LPM for this host, disabling LPM.
[    1.798171] usb usb6: New USB device found, idVendor=1d6b, idProduct=0003, bcdDevice= 5.10
[    1.798183] usb usb6: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[    1.798192] usb usb6: Product: xHCI Host Controller
[    1.798200] usb usb6: Manufacturer: Linux 5.10.97 xhci-hcd
[    1.798207] usb usb6: SerialNumber: xhci-hcd.3.auto
[    1.798654] hub 6-0:1.0: USB hub found
[    1.798703] hub 6-0:1.0: 1 port detected
[    1.799192] usbcore: registered new interface driver cdc_wdm
[    1.799495] usbcore: registered new interface driver uas
[    1.799624] usbcore: registered new interface driver usb-storage
[    1.799743] usbcore: registered new interface driver usbserial_generic
[    1.799772] usbserial: USB Serial support registered for generic
[    1.799829] usbcore: registered new interface driver cp210x
[    1.799858] usbserial: USB Serial support registered for cp210x
[    1.799935] usbcore: registered new interface driver ftdi_sio
[    1.799961] usbserial: USB Serial support registered for FTDI USB Serial Device
[    1.800143] usbcore: registered new interface driver keyspan
[    1.800170] usbserial: USB Serial support registered for Keyspan - (without firmware)
[    1.800199] usbserial: USB Serial support registered for Keyspan 1 port adapter
[    1.800225] usbserial: USB Serial support registered for Keyspan 2 port adapter
[    1.800251] usbserial: USB Serial support registered for Keyspan 4 port adapter
[    1.800303] usbcore: registered new interface driver option
[    1.800328] usbserial: USB Serial support registered for GSM modem (1-port)
[    1.800582] usbcore: registered new interface driver oti6858
[    1.800609] usbserial: USB Serial support registered for oti6858
[    1.800661] usbcore: registered new interface driver pl2303
[    1.800687] usbserial: USB Serial support registered for pl2303
[    1.800747] usbcore: registered new interface driver qcserial
[    1.800777] usbserial: USB Serial support registered for Qualcomm USB modem
[    1.800845] usbcore: registered new interface driver sierra
[    1.800873] usbserial: USB Serial support registered for Sierra USB modem
[    1.802261] usbcore: registered new interface driver usbtouchscreen
[    1.802830] .. rk pwm remotectl v2.0 init
[    1.803108] input: fe6e0030.pwm as /devices/platform/fe6e0030.pwm/input/input0
[    1.803517] remotectl-pwm fe6e0030.pwm: pwm version is 0x2130000
[    1.803576] remotectl-pwm fe6e0030.pwm: Controller support pwrkey capture
[    1.804407] i2c /dev entries driver
[    1.807430] fan53555-regulator 0-001c: FAN53555 Option[12] Rev[15] Detected!
[    1.808886] vdd_cpu: supplied by vcc5v0_sys
[    1.812537] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[    1.816671] rk808 0-0020: chip id: 0x8090
[    1.816728] rk808 0-0020: No cache defaults, reading back from HW
[    1.840458] rk808 0-0020: source: on=0x40, off=0x00
[    1.840489] rk808 0-0020: support dcdc3 fb mode:-22, 0
[    1.840501] rk808 0-0020: support pmic reset mode:0,0
[    1.845344] rk808-regulator rk808-regulator: there is no dvs0 gpio
[    1.845400] rk808-regulator rk808-regulator: there is no dvs1 gpio
[    1.845498] vdd_logic: supplied by vcc3v3_sys
[    1.846288] vdd_gpu: supplied by vcc3v3_sys
[    1.846977] vcc_ddr: supplied by vcc3v3_sys
[    1.847657] vdd_npu: supplied by vcc3v3_sys
[    1.848360] vcc_1v8: supplied by vcc3v3_sys
[    1.849025] vdda0v9_image: supplied by vcc3v3_sys
[    1.850211] vdda_0v9: supplied by vcc3v3_sys
[    1.851408] vdda0v9_pmu: supplied by vcc3v3_sys
[    1.852659] vccio_acodec: supplied by vcc3v3_sys
[    1.853870] vccio_sd: supplied by vcc3v3_sys
[    1.855062] vcc3v3_pmu: supplied by vcc3v3_sys
[    1.856265] vcca_1v8: supplied by vcc3v3_sys
[    1.857465] vcca1v8_pmu: supplied by vcc3v3_sys
[    1.858679] vcca1v8_image: supplied by vcc3v3_sys
[    1.859868] vcc_3v3: supplied by vcc3v3_sys
[    1.860532] vcc3v3_sd: supplied by vcc3v3_sys
[    1.861187] rk817-battery: Failed to locate of_node [id: -1]
[    1.861362] rk817-battery rk817-battery: Failed to find matching dt id
[    1.861481] rk817-charger: Failed to locate of_node [id: -1]
[    1.861588] rk817-charger rk817-charger: Failed to find matching dt id
[    1.864699] input: rk805 pwrkey as /devices/platform/fdd40000.i2c/i2c-0/0-0020/rk805-pwrkey/input/input1
[    1.871074] rk808-rtc rk808-rtc: registered as rtc0
[    1.872817] rk808-rtc rk808-rtc: setting system clock to 2017-08-05T09:20:47 UTC (1501924847)
[    1.877623] i2c i2c-4: 1 i2c clients have been registered at 0x36
[    1.882649] rtc-hym8563 5-0051: no valid clock/calendar values available
[    1.882870] rtc-hym8563 5-0051: registered as rtc1
[    1.884795] goodix_ts_probe() start
[    1.884890] Goodix-TS 5-005d: supply tp not found, using dummy regulator
[    1.905877] usb 1-1: new high-speed USB device number 2 using ehci-platform
[    2.016659] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[    2.054228] usb 1-1: New USB device found, idVendor=05e3, idProduct=0608, bcdDevice=85.38
[    2.054251] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[    2.054261] usb 1-1: Product: USB2.0 Hub
[    2.055108] hub 1-1:1.0: USB hub found
[    2.055473] hub 1-1:1.0: 4 ports detected
[    2.112529] <<-GTP-ERROR->> GTP i2c test failed time 1.
[    2.129988] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[    2.225864] <<-GTP-ERROR->> GTP i2c test failed time 2.
[    2.243338] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[    2.339198] <<-GTP-ERROR->> GTP i2c test failed time 3.
[    2.356662] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[    2.452516] <<-GTP-ERROR->> GTP i2c test failed time 4.
[    2.469972] <<-GTP-ERROR->> I2C Read: 0x8047, 1 bytes failed, errcode: -6! Process reset.
[    2.565863] <<-GTP-ERROR->> GTP i2c test failed time 5.
[    2.582533] <goodix_ts_probe>_2790    I2C communication ERROR!
[    2.582553]    <goodix_ts_probe>_2865  prob error !!!!!!!!!!!!!!!
[    2.582611] ------------[ cut here ]------------
[    2.582632] WARNING: CPU: 2 PID: 1 at ../../src_tmp/linux-5.10/drivers/regulator/core.c:2159 _regulator_put+0x150/0x158
[    2.582640] Modules linked in:
[    2.582654] CPU: 2 PID: 1 Comm: swapper/0 Not tainted 5.10.97 #1
[    2.582661] Hardware name: rockchip,rk3568-toybrick-dev-linux-x0 (DT)
[    2.582671] pstate: 80c00009 (Nzcv daif +PAN +UAO -TCO BTYPE=--)
[    2.582680] pc : _regulator_put+0x150/0x158
[    2.582688] lr : regulator_put+0x38/0x50
[    2.582694] sp : ffffffc011b4b5d0
[    2.582700] x29: ffffffc011b4b5d0 x28: ffffffc0119fe000 
[    2.582711] x27: ffffff81f2f07c00 x26: ffffff81f2f0dc00 
[    2.582722] x25: ffffffc011b4b638 x24: ffffffc011aa9000 
[    2.582733] x23: ffffffc0113cfc5a x22: ffffffc0113e41d6 
[    2.582742] x21: ffffff81f2f0de00 x20: ffffffc0118fdd20 
[    2.582753] x19: ffffff81f2f0df00 x18: 0000000000000000 
[    2.582764] x17: 0000000000000000 x16: 0000000000020000 
[    2.582773] x15: 0000000000010000 x14: 0000000000008000 
[    2.582785] x13: ffffff81f2f0dc00 x12: ffffff81f0c5a350 
[    2.582796] x11: 0000000000000000 x10: 0000000000000000 
[    2.582806] x9 : ffffffc01072f4cc x8 : 0000000000000001 
[    2.582816] x7 : 0000000000000000 x6 : ffffffc0118ecc20 
[    2.582826] x5 : 00011b10fa8450ae x4 : ffffff81f0caa480 
[    2.582836] x3 : 0000000000000000 x2 : ffffff81f0c5a350 
[    2.582845] x1 : ffffff81f2f0de80 x0 : ffffff81f2f0df00 
[    2.582857] Call trace:
[    2.582867]  _regulator_put+0x150/0x158
[    2.582875]  regulator_put+0x38/0x50
[    2.582886]  devm_regulator_release+0x20/0x2c
[    2.582896]  release_nodes+0x1cc/0x244
[    2.582903]  devres_release_all+0x48/0x64
[    2.582912]  really_probe+0x18c/0x478
[    2.582920]  driver_probe_device+0xec/0x164
[    2.582927]  __device_attach_driver+0xa8/0x120
[    2.582934]  bus_for_each_drv+0x8c/0xd8
[    2.582942]  __device_attach+0xc4/0x178
[    2.582949]  device_initial_probe+0x20/0x2c
[    2.582956]  bus_probe_device+0x40/0xa0
[    2.582965]  device_add+0x6cc/0x75c
[    2.582974]  device_register+0x2c/0x3c
[    2.582983]  i2c_new_client_device+0x1e4/0x2d8
[    2.582992]  of_i2c_register_devices+0xfc/0x1e0
[    2.582999]  i2c_register_adapter+0x49c/0x62c
[    2.583006]  __i2c_add_numbered_adapter+0x64/0x98
[    2.583014]  i2c_add_adapter+0x48/0xc8
[    2.583022]  rk3x_i2c_probe+0x324/0x400
[    2.583030]  platform_drv_probe+0xa0/0xc0
[    2.583038]  really_probe+0x158/0x478
[    2.583045]  driver_probe_device+0xec/0x164
[    2.583053]  device_driver_attach+0x58/0x7c
[    2.583060]  __driver_attach+0xd4/0x160
[    2.583067]  bus_for_each_dev+0x88/0xd4
[    2.583074]  driver_attach+0x30/0x3c
[    2.583081]  bus_add_driver+0x118/0x20c
[    2.583088]  driver_register+0x70/0x108
[    2.583096]  __platform_driver_register+0x50/0x5c
[    2.583106]  rk3x_i2c_driver_init+0x28/0x34
[    2.583115]  do_one_initcall+0x108/0x298
[    2.583123]  do_initcall_level+0x110/0x130
[    2.583130]  do_initcalls+0x5c/0x9c
[    2.583136]  do_basic_setup+0x2c/0x38
[    2.583143]  kernel_init_freeable+0x104/0x150
[    2.583152]  kernel_init+0x20/0x118
[    2.583160]  ret_from_fork+0x10/0x30
[    2.583171] ---[ end trace 98b69c759ce5862a ]---
[    2.584611] ov5695 4-0036-1: supply avdd not found, using dummy regulator
[    2.584793] ov5695 4-0036-1: supply dovdd not found, using dummy regulator
[    2.584895] ov5695 4-0036-1: supply dvdd not found, using dummy regulator
[    2.586380] ov5695 4-0036-1: Unexpected sensor id(000000), ret(-5)
[    2.586742] ov5695: probe of 4-0036-1 failed with error -5
[    2.588513] rkisp_hw fdff0000.rkisp: Adding to iommu group 6
[    2.588750] rkisp_hw fdff0000.rkisp: is_thunderboot: 0
[    2.588765] rkisp_hw fdff0000.rkisp: max input:0x0@0fps
[    2.588797] rkisp_hw fdff0000.rkisp: can't request region for resource [mem 0xfdff0000-0xfdffffff]
[    2.589892] rkisp rkisp-vir0: rkisp driver version: v01.08.00
[    2.590024] rkisp rkisp-vir0: No memory-region-thunderboot specified
[    2.590291] rkisp rkisp-vir0: Entity type for entity rkisp-isp-subdev was not initialized!
[    2.590314] rkisp rkisp-vir0: Entity type for entity rkisp-csi-subdev was not initialized!
[    2.593073] usbcore: registered new interface driver uvcvideo
[    2.593095] USB Video Class driver (1.1.1)
[    2.595891] rockchip-thermal fe710000.tsadc: tsadc is probed successfully!
[    2.597429] Bluetooth: HCI UART driver ver 2.3
[    2.597452] Bluetooth: HCI UART protocol H4 registered
[    2.597460] Bluetooth: HCI UART protocol ATH3K registered
[    2.597550] usbcore: registered new interface driver bfusb
[    2.597620] usbcore: registered new interface driver btusb
[    2.597954] cpu cpu0: Failed to get cpu_leakage
[    2.612623] cpu cpu0: temp=40000, pvtm=87408 (87408 + 0)
[    2.612918] cpu cpu0: pvtm-volt-sel=1
[    2.614749] cpu cpu0: avs=0
[    2.615074] cpu cpu0: EM: created perf domain
[    2.615204] cpu cpu0: l=0 h=2147483647 hyst=5000 l_limit=0 h_limit=0 h_table=0
[    2.621644] sdhci: Secure Digital Host Controller Interface driver
[    2.621668] sdhci: Copyright(c) Pierre Ossman
[    2.621675] Synopsys Designware Multimedia Card Interface Driver
[    2.622626] sdhci-pltfm: SDHCI platform and OF driver helper
[    2.623099] rockchip-pinctrl pinctrl: pin gpio2-2 already requested by fe570000.can; cannot claim for fe2b0000.dwmmc
[    2.623122] rockchip-pinctrl pinctrl: pin-66 (fe2b0000.dwmmc) status -22
[    2.623167] rockchip-pinctrl pinctrl: could not request pin 66 (gpio2-2) from group sdmmc0-clk  on device rockchip-pinctrl
[    2.623178] dwmmc_rockchip fe2b0000.dwmmc: Error applying setting, reverse things back
[    2.623223] dwmmc_rockchip: probe of fe2b0000.dwmmc failed with error -22
[    2.623358] dwmmc_rockchip fe000000.dwmmc: IDMAC supports 32-bit address mode.
[    2.623399] dwmmc_rockchip fe000000.dwmmc: Using internal DMA controller.
[    2.623414] dwmmc_rockchip fe000000.dwmmc: Version ID is 270a
[    2.623481] dwmmc_rockchip fe000000.dwmmc: DW MMC controller at irq 50,32 bit host data width,256 deep fifo
[    2.623962] dwmmc_rockchip fe000000.dwmmc: allocated mmc-pwrseq
[    2.623986] mmc_host mmc3: card is non-removable.
[    2.624987] SMCCC: SOC_ID: ARCH_SOC_ID not implemented, skipping ....
[    2.625540] hid: raw HID events driver (C) Jiri Kosina
[    2.626146] usbcore: registered new interface driver usbhid
[    2.626163] usbhid: USB HID core driver
[    2.626675] ashmem: initialized
[    2.626927] zrhung hung_wp_screen_init start
[    2.627321] zrhung hung_wp_screen_init done
[    2.627907] rockchip,bus bus-npu: Failed to get leakage
[    2.627933] rockchip,bus bus-npu: pvtm = 87408, form pvtm_value
[    2.627953] rockchip,bus bus-npu: pvtm-volt-sel=1
[    2.628229] rockchip,bus bus-npu: avs=0
[    2.634431] optee: probing for conduit method.
[    2.634475] optee: revision 3.13 (631d7ed9)
[    2.635125] optee: initialized driver
[    2.635819] access_token_id: access_tokenid init success
[    2.637984] rk817-codec rk817-codec: DMA mask not set
[    2.643553] rockchip-pinctrl pinctrl: pin gpio1-9 already requested by 3c0000000.pcie; cannot claim for fe410000.i2s
[    2.643606] rockchip-pinctrl pinctrl: pin-41 (fe410000.i2s) status -22
[    2.643621] rockchip-pinctrl pinctrl: could not request pin 41 (gpio1-9) from group i2s1m0-sdi2  on device rockchip-pinctrl
[    2.643631] rockchip-i2s-tdm fe410000.i2s: Error applying setting, reverse things back
[    2.643645] rockchip-pinctrl pinctrl: not freeing pin 36 (gpio1-4) as part of deactivating group i2s1m0-sclkrx - it is already used for some other setting
[    2.643699] rockchip-i2s-tdm: probe of fe410000.i2s failed with error -22
[    2.646452] rockchip-pinctrl pinctrl: pin gpio1-4 already requested by fe410000.i2s; cannot claim for fe460000.spdif
[    2.646481] rockchip-pinctrl pinctrl: pin-36 (fe460000.spdif) status -22
[    2.646495] rockchip-pinctrl pinctrl: could not request pin 36 (gpio1-4) from group spdifm0-tx  on device rockchip-pinctrl
[    2.646505] rockchip-spdif fe460000.spdif: Error applying setting, reverse things back
[    2.646531] rockchip-spdif: probe of fe460000.spdif failed with error -22
[    2.649236] xt_time: kernel timezone is -0000
[    2.649723] Initializing XFRM netlink socket
[    2.650335] NET: Registered protocol family 10
[    2.651753] Segment Routing with IPv6
[    2.651885] NET: Registered protocol family 17
[    2.651924] NET: Registered protocol family 15
[    2.651935] can: controller area network core
[    2.651992] NET: Registered protocol family 29
[    2.652003] can: raw protocol
[    2.652016] can: broadcast manager protocol
[    2.652033] can: netlink gateway - max_hops=1
[    2.652366] Bluetooth: RFCOMM socket layer initialized
[    2.652419] Bluetooth: RFCOMM ver 1.11
[    2.652442] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[    2.652459] Bluetooth: HIDP socket layer initialized
[    2.652920] [BT_RFKILL]: Enter rfkill_rk_init
[    2.652937] [WLAN_RFKILL]: Enter rfkill_wlan_init
[    2.653726] [WLAN_RFKILL]: Enter rfkill_wlan_probe
[    2.653809] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi_chip_type = rtl8822ce
[    2.653821] [WLAN_RFKILL]: wlan_platdata_parse_dt: enable wifi power control.
[    2.653830] [WLAN_RFKILL]: wlan_platdata_parse_dt: wifi power controled by gpio.
[    2.653863] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,poweren_gpio = 125 flags = 0.
[    2.653901] [WLAN_RFKILL]: wlan_platdata_parse_dt: WIFI,host_wake_irq = 74, flags = 1.
[    2.653919] [WLAN_RFKILL]: wlan_platdata_parse_dt: The ref_wifi_clk not found !
[    2.653928] [WLAN_RFKILL]: rfkill_wlan_probe: init gpio
[    2.653943] [WLAN_RFKILL]: Failed to get rkwifi_wlan_poweren gpio.
[    2.653977] wlan-platdata: probe of wireless-wlan failed with error -1
[    2.654678] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: uart_rts_gpios = 73.
[    2.654719] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,reset_gpio = 96.
[    2.654743] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_gpio = 97.
[    2.654765] [BT_RFKILL]: bluetooth_platdata_parse_dt: get property: BT,wake_host_irq = 98.
[    2.654844] [BT_RFKILL]: Failed to get bt_default_wake_host gpio.
[    2.654970] rfkill_bt: probe of wireless-bluetooth failed with error -1
[    2.655096] Key type dns_resolver registered
[    2.655464] mmc0: SDHCI controller on fe310000.sdhci [fe310000.sdhci] using ADMA
[    2.656274] gc8034 4-0037: driver version: 00.01.07
[    2.656340] gc8034 4-0037: Failed to get power-gpios, maybe no use
[    2.656499] gc8034 4-0037: Failed to get pwdn-gpios
[    2.656585] gc8034 4-0037: supply avdd not found, using dummy regulator
[    2.656835] gc8034 4-0037: supply dovdd not found, using dummy regulator
[    2.656938] gc8034 4-0037: supply dvdd not found, using dummy regulator
[    2.657030] gc8034 4-0037: lane_num(4)  pixel_rate(319887360)
[    2.657050] gc8034 4-0037: could not get default pinstate
[    2.657061] gc8034 4-0037: could not get sleep pinstate
[    2.663151] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 400000Hz, actual 375000HZ div = 0)
[    2.729085] mmc0: new HS200 MMC card at address 0001
[    2.729233] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 300000Hz, actual 187500HZ div = 1)
[    2.729858] mmcblk0: mmc0:0001 DA4032 29.1 GiB 
[    2.730154] mmcblk0boot0: mmc0:0001 DA4032 partition 1 4.00 MiB
[    2.730448] mmcblk0boot1: mmc0:0001 DA4032 partition 2 4.00 MiB
[    2.730657] mmcblk0rpmb: mmc0:0001 DA4032 partition 3 16.0 MiB, chardev (237:0)
[    2.734100]  mmcblk0: p1 p2 p3 p4 p5 p6 p7 p8 p9 p10 p11
[    2.745708] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[    2.795915] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 200000Hz, actual 187500HZ div = 1)
[    2.812476] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[    2.825888] rk-pcie 3c0000000.pcie: PCIe Linking... LTSSM is 0x3
[    2.865900] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 100000Hz, actual 93750HZ div = 2)
[    2.886277] mmc_host mmc3: Bus speed (slot 0) = 375000Hz (slot req 375000Hz, actual 375000HZ div = 0)
[    3.162509] gc8034 4-0037: gc8034 read reg:0xf0 failed !
[    3.162776] gc8034 4-0037: gc8034 read reg:0xf1 failed !
[    3.162786] gc8034 4-0037: Unexpected sensor id(000000), ret(-6)
[    3.163512] core_ctl: Creating CPU group 0
[    3.163522] core_ctl: Init CPU0 state
[    3.163527] core_ctl: Init CPU1 state
[    3.163531] core_ctl: Init CPU2 state
[    3.163536] core_ctl: Init CPU3 state
[    3.164043] Loading compiled-in X.509 certificates
[    3.164255] run reclaimacct_init successfully
[    3.164293] Key type ._fscrypt registered
[    3.164295] enabled
[    3.164305] Key type .fscrypt registered
[    3.164311] Key type fscrypt-provisioning registered
[    3.165615] pstore: Using crash dump compression: deflate
[    3.167259] rga2: Driver loaded successfully ver:3.2.63318
[    3.167719] rga2: Module initialized.
[    3.195537] rockchip-cpuinfo cpuinfo: failed to get id cell: -517
[    3.197264] mali fde60000.gpu: Kernel DDK version g2p0-01eac0
[    3.197589] mali fde60000.gpu: dev_pm_opp_set_regulators: no regulator (shadercores) found: -19
[    3.197678] mali fde60000.gpu: Failed to get gpu_leakage
[    3.198087] mali fde60000.gpu: avs=0
[    3.198103] W : [File] : ../../src_tmp/linux-5.10/drivers/gpu/arm/bifrost/platform/rk/mali_kbase_config_rk.c; [Line] : 112; [Func] : kbase_platform_rk_init(); power-off-delay-ms not available.
[    3.198569] mali fde60000.gpu: GPU identified as 0x2 arch 7.4.0 r1p0 status 0
[    3.198657] mali fde60000.gpu: No memory group manager is configured
[    3.199136] mali fde60000.gpu: l=-2147483648 h=2147483647 hyst=0 l_limit=0 h_limit=0 h_table=0
[    3.199209] mali fde60000.gpu: Failed to get gpu_leakage
[    3.199992] mali fde60000.gpu: Probed as mali0
[    3.200569] input: adc-keys as /devices/platform/adc-keys/input/input2
[    3.201328] of_clk_hw_onecell_get: invalid index 3
[    3.201348] rockchip-dmc dmc: Cannot get the clk dmc_clk. If using SCMI, trusted firmware need update to V1.01 and above.
[    3.201441] rockchip-dmc: probe of dmc failed with error -2
[    3.203267] rockchip-cpuinfo cpuinfo: failed to get id cell: -517
[    3.204674] rk_iommu fde4b000.iommu: deferred probe timeout, ignoring dependency
[    3.204701] rk_iommu: probe of fde4b000.iommu failed with error -110
[    3.204909] rockchip-cpuinfo cpuinfo: failed to get id cell: -517
[    3.206248] cfg80211: Loading compiled-in X.509 certificates for regulatory database
[    3.207694] cfg80211: Loaded X.509 cert 'sforshee: 00b28ddf47aef9cea7'
[    3.207762] I : [File] : ../../src_tmp/linux-5.10/drivers/gpu/arm/mali400/mali/linux/mali_kernel_linux.c; [Line] : 409; [Func] : mali_module_init(); svn_rev_string_from_arm of this mali_ko is '', rk_ko_ver is '5', built at '15:18:35', on 'Jan 11 2024'.
[    3.208254] Mali: 
[    3.208256] Mali device driver loaded
[    3.208275] rkisp rkisp-vir0: clear unready subdev num: 3
[    3.208284] rockchip-csi2-dphy0: No link between dphy and sensor
[    3.208460] platform regulatory.0: Direct firmware load for regulatory.db failed with error -2
[    3.208473] cfg80211: failed to load regulatory.db
[    3.208681] rockchip-csi2-dphy0: No link between dphy and sensor
[    3.208689] rkisp-vir0: update sensor failed
[    3.208699] ALSA device list:
[    3.208707]   No soundcards found.
[    3.211374] Freeing unused kernel memory: 1536K
[    3.239508] Run /init as init process
[    3.239922] Failed to execute /init (error -26)
[    3.239942] Run /sbin/init as init process
[    3.240108] Run /etc/init as init process
[    3.240273] Run /bin/init as init process
[    3.240477] Starting init: /bin/init exists but couldn't execute it (error -26)
[    3.240494] Run /bin/sh as init process
[    3.240698] Starting init: /bin/sh exists but couldn't execute it (error -26)
[    3.240718] Kernel panic - not syncing: No working init found.  Try passing init= option to kernel. See Linux Documentation/admin-guide/init.rst for guidance.
[    3.244369] CPU: 0 PID: 1 Comm: swapper/0 Tainted: G        W         5.10.97 #1
[    3.245042] Hardware name: rockchip,rk3568-toybrick-dev-linux-x0 (DT)
[    3.245626] Call trace:
[    3.245887]  dump_backtrace+0x0/0x1e4
[    3.246238]  show_stack+0x24/0x30
[    3.246564]  dump_stack+0xc0/0x11c
[    3.246887]  panic+0x15c/0x358
[    3.247181]  kernel_init+0xf0/0x118
[    3.247515]  ret_from_fork+0x10/0x30
[    3.247863] SMP: stopping secondary CPUs
[    3.248240] PMU CRU:
[    3.248478] 00000000: 00006064 00001481 00000000 00000007 00007f00 00000000 00000000 00000000
[    3.249261] 00000020: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.250044] 00000040: 00001129 00001588 00000000 00000007 00007f00 00000000 00000000 00000000
[    3.250826] 00000060: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.251607] 00000080: 00000005 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.252388] 000000a0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.253169] 000000c0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.253949] 000000e0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.254731] 00000100: 00000080 0040b71b 00000001 00000001 00000800 00000000 00000001 00000009
[    3.255512] 00000120: 0000050f 00008888 00000000 00000000 00000000 00000000 00000000 00000000
[    3.256293] 00000140: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.257074] 00000160: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.257856] 00000180: 00000000 000000c3 00000000 00000000 00000000 00000000 00000000 00000000
[    3.258636] 000001a0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.259418] 000001c0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.260199] 000001e0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.260980] 00000200: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.261761] 00000220: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.262530] 00000240: 00040020 00000000
[    3.262880] CRU:
[    3.263073] 00000000: 00002044 00001481 00000000 00000007 00007f00 00000000 00000000 00000000
[    3.263855] 00000020: 00004082 00001441 00000000 00000007 00007f00 00000000 00000000 00000000
[    3.264636] 00000040: 00002063 00001441 00000000 00000007 00007f00 00000000 00000000 00000000
[    3.265417] 00000060: 0000107d 00001443 00000000 00000007 00007f00 00000000 00000000 00000000
[    3.266186] 00000080: 00002064 00001441 00000000 00000000 00000000 00000000 00000000 00000000
[    3.266956] 000000a0: 00001145 00001486 00000000 00000000 00000000 00000000 00000000 00000000
[    3.267738] 000000c0: 00005455 00000000 00000000 00000000 00640064 00000000 00000000 00000103
[    3.268518] 000000e0: 00000001 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.269299] 00000100: 000000c0 00000000 00000001 00000101 00000202 00000111 00004191 00000011
[    3.270080] 00000120: 00000053 00000100 00000001 00008000 00010001 00008000 00010001 00000401
[    3.270862] 00000140: 01003057 00008000 00010001 00008000 00010001 00008000 00010001 00004000
[    3.271645] 00000160: 00010001 0000000b 00000000 00000010 00001031 00001c30 00000520 00000000
[    3.272425] 00000180: 00000520 00000000 00000310 0000c001 0000c0c0 00003100 00000001 00000000
[    3.273207] 000001a0: 00000409 00000003 00000103 00002100 00000203 00000003 00000000 00000103
[    3.273987] 000001c0: 00000003 00000303 00000001 00001725 0000200b 00000000 0000200b 00000000
[    3.274770] 000001e0: 0000200b 00000000 0000200b 00000000 0000200b 00000000 0000200b 00000000
[    3.275551] 00000200: 0000200b 00000000 0000200b 00000000 0000200b 00000000 00000307 00000203
[    3.276334] 00000220: 00001500 00000000 0000001f 00000302 00000705 00000f0b 0000013b 00000303
[    3.277116] 00000240: 00000f07 00002713 00001f09 00008000 00010001 00003b2f 00000101 00000302
[    3.277898] 00000260: 00000704 0000130f 00001f27 00000000 00000000 00000000 00000000 00000000
[    3.278680] 00000280: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.279459] 000002a0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.280238] 000002c0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.281020] 000002e0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.281800] 00000300: 00000000 00000600 00000009 00000000 00000000 00000000 00003333 0000c333
[    3.282580] 00000320: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.283361] 00000340: 00000000 00000003 00000007 00000100 00001000 00000000 00001033 0000f1b3
[    3.284141] 00000360: 000001c3 000001f3 00000000 00000000 00000990 00000900 000003d1 00000000
[    3.284922] 00000380: 00000400 00000000 00000000 00008000 00000000 00000000 00000000 00000000
[    3.285702] 000003a0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.286471] 000003c0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.287250] 000003e0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.288029] 00000400: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.288810] 00000420: 00000000 00000000 00000000 00000002 00000002 00000000 00000000 00000000
[    3.289590] 00000440: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.290372] 00000460: 00000000 00000000 00000400 00000000 00000000 00000000 00000000 00000000
[    3.291151] 00000480: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.291933] 000004a0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.292713] 000004c0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.293495] 000004e0: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.294276] 00000500: 00040020 00000000 00040020 00000000 00040020 00000000 00040020 00000000
[    3.295059] 00000520: 00040020 00000000 00040020 00000000 00040020 00000000 00040020 00000000
[    3.295842] 00000540: 00040020 00000000 00040020 00000000 00000000 00000000 00000000 00000000
[    3.296622] 00000560: 00000000 00000000 00000000 00000000 00000000 00000000 00000000 00000000
[    3.297390] 00000580: 00000004 00000000
[    3.354951] Call trace:
[    3.355225]  dump_backtrace+0x0/0x1e4
[    3.355581]  show_stack+0x24/0x30
[    3.355907]  bbox_notify_error+0x90/0x1b8
[    3.356288]  bbox_task_panic+0x60/0x90
[    3.356648]  atomic_notifier_call_chain+0x50/0x8c
[    3.357095]  panic+0x188/0x358
[    3.357390]  kernel_init+0xf0/0x118
[    3.357721]  ret_from_fork+0x10/0x30
[    3.358067] bbox:[info][blackbox_core.c:302] [SYSTEM] starts dumping data!
[    3.358832] bbox:[info][blackbox_core.c:304] [SYSTEM] ends dumping data!
[    3.359444] bbox:[info][blackbox_core.c:307] [SYSTEM] starts resetting!
DDR Version V1.10 20210810
In
ddrconfig:0
LP4 MR14:0x4d
LPDDR4, 324MHz
BW=32 Col=10 Bk=8 CS0 Row=17 CS=1 Die BW=16 Size=4096MB
tdqss: cs0 dqs0: 361ps, dqs1: 289ps, dqs2: 337ps, dqs3: 241ps, 

change to: 324MHz
PHY drv:clk:38,ca:38,DQ:30,odt:0
vrefinner:41%, vrefout:41%
dram drv:40,odt:0
clk skew:0x58

change to: 528MHz
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x78

change to: 780MHz
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:41%
dram drv:40,odt:0
clk skew:0x5c

change to: 1560MHz(final freq)
PHY drv:clk:38,ca:38,DQ:30,odt:60
vrefinner:16%, vrefout:29%
dram drv:40,odt:80
vref_ca:00000068
clk skew:0x1a
cs 0:
the read training result:
DQS0:0x30, DQS1:0x32, DQS2:0x36, DQS3:0x30, 
min  : 0xd  0xe 0x10  0xc  0x2  0x5  0x8  0x3 , 0xb  0x7  0x2  0x2  0xe  0xc 0x10  0x9 ,
      0x13 0x12  0xd  0xb  0x3  0x1  0x4  0x6 , 0xe  0xa  0xa  0x2 0x11 0x12  0xf 0x10 ,
mid  :0x27 0x28 0x29 0x26 0x1b 0x1e 0x22 0x1e ,0x25 0x22 0x1c 0x1d 0x28 0x24 0x2a 0x24 ,
      0x2e 0x2c 0x27 0x25 0x1e 0x1c 0x1e 0x1f ,0x29 0x24 0x24 0x1c 0x2b 0x2c 0x29 0x2b ,
max  :0x42 0x42 0x43 0x41 0x34 0x37 0x3d 0x39 ,0x3f 0x3d 0x37 0x39 0x43 0x3d 0x44 0x3f ,
      0x49 0x47 0x42 0x3f 0x39 0x37 0x38 0x39 ,0x44 0x3e 0x3e 0x37 0x46 0x46 0x43 0x47 ,
range:0x35 0x34 0x33 0x35 0x32 0x32 0x35 0x36 ,0x34 0x36 0x35 0x37 0x35 0x31 0x34 0x36 ,
      0x36 0x35 0x35 0x34 0x36 0x36 0x34 0x33 ,0x36 0x34 0x34 0x35 0x35 0x34 0x34 0x37 ,
the write training result:
DQS0:0x62, DQS1:0x53, DQS2:0x5d, DQS3:0x4a, 
min  :0xaa 0xaf 0xb2 0xae 0xa0 0xa3 0xa6 0xa9 0xa7 ,0x9c 0x9a 0x96 0x97 0x9f 0x9e 0x9f 0xa0 0x99 ,
      0xa7 0xa8 0xa3 0xa3 0x9a 0x99 0x9a 0xa0 0xa0 ,0x95 0x94 0x93 0x8e 0x9d 0x9a 0x97 0x9f 0x93 ,
mid  :0xc7 0xca 0xce 0xc9 0xbb 0xbf 0xc2 0xc3 0xc2 ,0xb8 0xb6 0xaf 0xb0 0xba 0xb8 0xb9 0xb9 0xb3 ,
      0xc4 0xc5 0xbd 0xbd 0xb5 0xb3 0xb5 0xba 0xba ,0xb1 0xae 0xad 0xa8 0xb7 0xb6 0xb2 0xb9 0xae ,
max  :0xe4 0xe6 0xea 0xe4 0xd6 0xdb 0xde 0xdd 0xdd ,0xd4 0xd2 0xc9 0xc9 0xd5 0xd2 0xd4 0xd2 0xce ,
      0xe2 0xe2 0xd8 0xd7 0xd1 0xcd 0xd0 0xd4 0xd5 ,0xcd 0xc9 0xc7 0xc2 0xd1 0xd2 0xcd 0xd4 0xc9 ,
range:0x3a 0x37 0x38 0x36 0x36 0x38 0x38 0x34 0x36 ,0x38 0x38 0x33 0x32 0x36 0x34 0x35 0x32 0x35 ,
      0x3b 0x3a 0x35 0x34 0x37 0x34 0x36 0x34 0x35 ,0x38 0x35 0x34 0x34 0x34 0x38 0x36 0x35 0x36 ,
CA Training result:
cs:0 min  :0x43 0x38 0x3c 0x2a 0x3d 0x28 0x3c ,0x43 0x2f 0x34 0x22 0x35 0x25 0x39 ,
cs:0 mid  :0x7b 0x7c 0x73 0x6e 0x72 0x6b 0x65 ,0x7a 0x75 0x6b 0x66 0x6a 0x68 0x62 ,
cs:0 max  :0xb4 0xc0 0xaa 0xb3 0xa8 0xaf 0x8f ,0xb1 0xbb 0xa2 0xaa 0xa0 0xac 0x8c ,
cs:0 range:0x71 0x88 0x6e 0x89 0x6b 0x87 0x53 ,0x6e 0x8c 0x6e 0x88 0x6b 0x87 0x53 ,
out
U-Boot SPL board init
U-Boot SPL 2017.09-ga1f6fc00a0-210413 #ldq (Apr 13 2021 - 11:35:00)
unknown raw ID phN
unrecognized JEDEC id bytes: 00, 00, 00
Trying to boot from MMC2
MMC error: The cmd index is 1, ret is -110
Card did not respond to voltage select!
mmc_init: -95, time 10
spl: mmc init failed with error: -95
Trying to boot from MMC1
SPL: A/B-slot: _a, successful: 0, tries-remain: 7
## Verified-boot: 0
## Checking atf-1 0x00040000 ... sha256+ OK
## Checking uboot 0x00a00000 ... sha256+ OK
## Checking fdt 0x00b2d008 ... sha256+ OK
## Checking atf-2 0xfdcc9000 ... sha256+ OK
## Checking atf-3 0xfdcd0000 ... sha256+ OK
## Checking optee 0x08400000 ... sha256+ OK
Jumping to U-Boot(0x00a00000) via ARM Trusted Firmware(0x00040000)
Total: 222.88 ms

INFO:    Preloader serial: 2
NOTICE:  BL31: v2.3():v2.3-135-gcda1658bc-dirty:xsf
NOTICE:  BL31: Built : 19:32:20, Jun  2 2021
INFO:    GICv3 without legacy support detected.
INFO:    ARM GICv3 driver initialized in EL3
INFO:    pmu v1 is valid
INFO:    dfs DDR fsp_param[0].freq_mhz= 1560MHz
INFO:    dfs DDR fsp_param[1].freq_mhz= 324MHz
INFO:    dfs DDR fsp_param[2].freq_mhz= 528MHz
INFO:    dfs DDR fsp_param[3].freq_mhz= 780MHz
INFO:    Using opteed sec cpu_context!
INFO:    boot cpu mask: 0
INFO:    BL31: Initializing runtime services
INFO:    BL31: Initializing BL32
I/TC: 
I/TC: OP-TEE version: 3.13.0-630-g631d7ed9a #hisping.lin (gcc version 10.2.1 20201103 (GNU Toolchain for the A-profile Architecture 10.2-2020.11 (arm-10.16))) #6 Mon Jan 17 19:07:43 CST 2022 aarch64
I/TC: Primary CPU initializing
I/TC: Primary CPU switching to normal world boot
INFO:    BL31: Preparing for EL3 exit to normal world
INFO:    Entry point address = 0xa00000
INFO:    SPSR = 0x3c9


U-Boot 2017.09-gb2f1de7c96-dirty #xu_yuntong (May 12 2022 - 16:08:39 +0800)
